It may seem difficult to put up a cat flap however, with the proper instructions it's not that hard. Firstly, determine how high you would like the flap to be (on average, belly height). Then, mark this area on your door and use the included template as a guide when drilling.

If you have a young kitten hold the door open a bit and gradually encourage it to enter. Reward it each time it goes through.

Measure the Door

A cat flap is an excellent way to allow your pet to move in and out of your house as it likes. This can help keep your cat in good health as it will ensure that it gets enough exercise and be able to go back inside when it is trapped in the elements during bad weather. It can also reduce the amount of time you have to allow it out or in. It will also help keep your home safe by allowing you to know when it has gone out.

However, it is essential that the cat flap is properly fitted to stop your pet from escaping through it or be pushed through by any other animals (e.g. dogs). You should measure the height of your pet's stomach and the height of the doorway at your home to ensure the flap is at the right height. If your cat flap cost is larger or shorter than the average, you can adjust the flap's position by moving it up or down by a tiny amount.

Next, use a spirit-level to mark the middle of the door. This is where you'll install the flap. Then, using the markings as an outline, cut the form of your flap on the door with a Jigsaw. Once you have cut out the door, sand the edges of the door to create smooth surfaces. You can then drill any fixing holes required.

The installation of a cat flap should not take more than two hours. The process can be slightly more complicated if you are required to install it on the form of a replacement upvc door panel with cat flap door or a composite one. This is because composite doors come in a variety of thicknesses, which can affect the way holes are cut. We always recommend to contact a professional if this is your first experience with glass.

Measure Your Cat

You can avoid hours of listening to the cat's meows to be allowed in or out. This is particularly helpful if you are at working all day and your cat flap installation bristol has to stay in the house waiting for you to get home regardless of the weather.

If you are planning to install a cat flap on your door, it is essential to measure your cat flap installers near me before attempting the task. Although it might seem like an easy task, it is essential to make sure you measure correctly or your cat may find it very difficult to use.

First, ensure that your cat is relaxed and not stressed before you take the measurements. You'll need to keep your cat in fitting a cat flap place in which they cannot move. Also, make sure that the measuring tape is straight and not bent against their body. You can get an accurate measurement by keeping the measuring tape or the ruler flat against the body of the animal from the top to the bottom.

Once you've got the measurement of your cat, it is time to take a look at the door and decide where you want to place the flap. Position the flap at the level of your cat's belly. This will allow them to pass through the door with minimal effort. This will also prevent the flap from making a lot noise when it swings back and forth.

You should consider the thickness of the uPVC or composite door as well. While all timber doors have a similar thickness to them, uPVC or composite doors are different in their overall structure. This makes the installation of the flap for your cat more difficult, as you must ensure that the hole is the right size.

You can make use of the template included in the instructions to mark the location of the hole on the door. This will allow you determine where the opening needs to be and also make sure the template is correctly positioned on the door. Using a spirit-level to ensure that the template is flush against the door can prove beneficial.

Cut the Flap

You'll need to make a hole in the door to accommodate your cat flap prior to you can attach it. This can be a challenging job, and it is recommended that you get help from a professional cat flap fitting service for this job in case you don't have the expertise or knowledge to tackle it yourself. It is also recommended that you read the instructions included with the cat flap kit to find out how to do it correctly.

To do this you need to take a measurement of the height of your cat or kitten's belly and use that as an indication point. A good guideline is to put the flap of your cat about 10 centimeters away from the ground since this is the typical height of the cat's belly. Your cat will be able to move through the flap with ease and also give the other cats or neighbours who are snooping a tough time trying to enter or leave.

Once you've determined the location where the cat flap needs to be located, mark the location on the door using the help of a pencil. If your kit comes with an outline of paper, place this over the door and use the markings to drill holes into each corner of the template. You will then be able to cut the template's shape and replace it with your cat flap.

If you are installing your cat flap on a door made from wood or uPVC, you can do it yourself if you feel confident enough to handle the Jigsaw. Ensure that you do not cut through any of the door's mullions, or cat flap fitting vertical rails. You can use a jigsaw to cut the panel into a square or cat flap fitting circle depending on the design of your cat flap. Take your time, and don't force the jigsaw into cutting faster.

Once the hole has been made, carefully place the cat flap into its new place of residence. Make sure it's securely secured. If the flap is fitted with screw caps then push them into the protruding bolts. Once the screws have been installed, sand the rough edges and then apply sealant to any gaps. This will prevent drafts from entering your home.

Place the Flap

If you have an ordinary cat flap, you can encourage your pet to go through it by placing a small amount cat food on the front of the door. You can also try pushing the cat with the help of a stick or your hands. Once your cat is accustomed to moving through the flap, it will be able to move into and out as it wishes, so you can let it in or out without having to be there to open the door for it all day (and likely in all weather conditions).

It is possible to install the flap inside a UPVC door or a glass door, however it might not be as easy as installing one in a wooden external door. This is because the doors made of UPVC and some kinds of glass doors don't have an even thickness. This can have a significant impact on how you cut the hole for the flap and will also affect whether the flap will fit properly once it's installed.

The mounting kit might include a template that shows you the best places to drill holes. If the kit does not come with a template, you can create one on your own. When cutting, it's important to avoid pushing the jigsaw too hard so that you don't create a bigger hole than is necessary in your door.

The majority of cat flaps are rectangular or square in shape but there are also some which are circular, and are typically more difficult to place. If you have a circular flap, it's essential to make sure the hole is in the right location on your door as if it's not, your cat will not be able to use the flap and could be left in the open all day (or even at night).

Certain cat flaps have locks that let you regulate when your cat can enter and leave. These can be very useful when you're worried about your cat going out at night and coming back in the darkness, or you're at work all day. The lock can be used to allow or deny entry, and some locks can be locked in both directions, permitting you to close the door completely, which is particularly beneficial for sick or elderly cats who aren't keen on going out in bad weather.